旋涂法制备WO3薄膜电致变色性能

"智能窗"大规模推广顺应可持续发展潮流,三氧化钨(WO_3)是生产"智能窗"的一种重要电致变色材料,但调控WO_3薄膜电致变色性能机制仍待进一步研究。采用旋涂法制备WO_3薄膜,重点研究了溶液浓度和旋涂次数对调控WO_3薄膜电致变色性能的影响。通过表面轮廓仪测量薄膜厚度,X射线衍射(XRD)测量薄膜结晶情况,原子力显微镜(AFM)和扫描电子显微镜(SEM)分析薄膜表面形貌,光谱仪测量薄膜初始态、着色态和褪色态的透射率。实验结果表明,随着溶液浓度增加(0. 2～1. 0 mol/L),薄膜厚度从9. 7 nm增加到33. 3 nm,透射率调制能力从0%提升到37. 0%;多次旋涂薄膜厚度线性增长,线性拟合优度(R~2)达0. 98,5次旋涂后透射率调制能力达51. 3%。改变溶液浓度和旋涂次数都是调控薄膜透射率调制能力的有效手段,精准调控薄膜透射率调制能力对设计不同应用场景的电致变色器件具有重大意义。     

Instantaneous work hardening behaviour of two-phase tungsten heavy alloys: a phenomenological approach

ABSTRACT

The present work describes a phenomenological approach to explain the instantaneous behaviour of tungsten heavy alloys (WHAs) in heat-treated and swaged conditions. The strengths and elongation values of heat-treated materials are lower and higher than those of the swaged samples respectively. The heat-treated materials exhibit two slopes in true stress–true plastic strain curves and follow the Ludwigson constitutive equation. On the other hand, swaged materials display a single slope and adhere to typical Swift constitutive equation. The latter reflect the presence of pre-strain in the materials due to swaging deformation. The fracture surfaces in heat-treated materials consist of W-W decohesion along with matrix rupture and W-cleavage, while swaged samples consist of mainly W-cleavage. Both the materials display three typical stages (I, II and III) of work hardening. The second derivatives of true stress–true plastic strain curves of these alloys exhibit a perfect parabola although the nature of true stress–true strain as well as true stress–true plastic strain curves is quite different in heat-treated and swaged materials. This has been observed for the first time in WHAs consisting of matrix and W-grains. The shape of the parabola is simple and easy to fit. The fitting parameters of parabolas have been successfully employed to explain the flow behaviour of a large number of tungsten heavy alloys having two-phase microstructure in different processing conditions.     

The Remarkably Robust,Photoactive Tungsten Iodide Cluster [W6I12(NCC6H5)2]

The new heteroleptic tungsten iodide cluster compound [W₆I₁₂(NCC₆H₅)₂] is presented. The synthesis is carried-out from Cs₂W₆I₁₄ and ZnI₂ under solvothermal conditions in benzonitrile solution, yielding red cube-shaped crystals. [W₆I₁₂(NCC₆H₅)₂] represents a heteroleptic [W₆I₈]-type cluster bearing four apical iodides and two benzonitrile ligands. Molecular [W₆I₁₂(NCC₆H₅)₂] clusters form a robust hydrogen bridged crystal structure with high thermal stability and high resistibility against hydrolysis. The electronic structure is analyzed by quantum chemical methods of the calculated electron localization function (ELF) and the band structure. Photoluminescence measurements are performed to verify and describe the photophysical properties of [W₆I₁₂(NCC₆H₅)₂]. Finally, the photocatalytic properties of [W₆I₁₂(NCC₆H₅)₂] are evaluated as a proof-of-concept.     

Compared catalytic properties of OMS-2-based nanocomposites for the degradation of organic pollutants

In this study,Mn catalysts have been designed based on manganese oxide octahedral molecular sieve(OMS-2) supports to optimize the catalytic activity in the degradation of organic pollutants.Herein,two different synthetic strategies:Pre-incorporation vs.wet-impregnation have been employed to synthesize[PW]-OMS-2 and [PW]/OMS-2.For [PW]-OMS-2,energy dispersive X-ray spectroscopy(EDX) confirmed that dispersed granular phosphotungstic acid attached and located at the surface of OMS-2,meanwhile some W atoms have been doped into frameworks of OMS-2.However,for [PW]/OMS-2,the W atoms cannot enter the OMS-2 frameworks.A correlation has been established between the different synthetic strategies and catalytic activities.The [PW]-OMS-2 is the most highly effective and stable over than[PW]/OMS-2 and OMS-2 itself for the organic pollutants removal.This may be caused not only by the synergetic effect of [PW] and OMS-2,but also by doping W into frameworks of OMS-2.Therefore,this work provides a new environmentally-friendly and heterogeneous PMS activator and it may be put into practice to degrade organic pollutants.     

可控表面磷原子修饰提升超细W2C纳米颗粒电解水析氢反应性能

研究高活性和稳定性的非贵金属基析氢催化剂对解决当前能源危机和环境污染问题具有重要意义.碳化钨具有与贵金属Pt类似的d带电子结构,因而成为一类新兴的非贵金属析氢催化剂,受到广泛关注.磷掺杂是提高催化剂析氢活性的有效方法之一,然而目前最常见的构筑磷掺杂方法是使用多金属氧酸盐(POMs,如H3PW12O40),其固定的W/P原子比导致W2C中的掺杂浓度难以调控,并且磷掺杂主要是进入碳载体而不是碳化物本身,从而导致无法明确杂原子对其电催化析氢活性的贡献.本文采用植酸(PA)为磷源设计合成了可控磷掺杂W2C纳米颗粒,并探讨了催化剂组分、杂原子掺杂位置与析氢性能之间的关系.深入研究了磷掺杂碳化钨(WCP)的化学结构和析氢活性.与原始的W2C催化剂相比,WCP具有更高的本征活性、更快的电子转移速率和更多的活性位数量,并且在酸性和碱性条件下均表现出较好的析氢性能.特别是过电位为-200 mV时,WCP催化剂的本征活性在酸性和碱性条件下分别为0.07和0.56 H2 s-1,高出纯W2C(0.01和0.05 H2 S-1)数倍.同时,在电流密度为-10 mA cm-2时,优化后的WCP催化剂在酸性和碱性条件下的析氢过电位分别降低了96和88 mV.XPS及EDS元素分析结果表明,随磷源添加量增加,磷掺杂从碳化钨表面逐渐向内部扩散,进一步说明磷取代位置与析氢活性之间的构效关系,高浓度的表面磷取代可以加速质子捕获过程,从而显著提高其析氢活性,而过量的内部磷取代会破坏W2C结构,降低电子转移速率,从而导致析氢性能下降.利用密度泛函理论计算深入研究了WCP具有较好析氢性能的原因,与内部磷取代相比,表面磷取代会使碳化钨表现出更合适的氢吸附自由能,并且更加有效地降低了氢释放势垒,从而优化了析氢反应动力学.综上,本文为元素掺杂工艺提供了新的思路,同时研究了表面异质原子对析氢活性的关键作用,为该类催化材料的构效关系研究提供了新思路.     

Binary Metal Oxide Adsorbed Graphene Modified Glassy Carbon Electrode for Detection of Riboflavin

Tungsten oxide (W) decorated titanium oxide (T) adsorbed onto a graphene (Gr) and modified the glassy carbon electrode for the electrochemical quantification of riboflavin (RF) in edible food and pharmaceuticals. For comparison, nanocomposites are formed using graphene oxide (GO), reduced graphene oxide (rGO) and pure graphite (G) sheets to study the electrochemical activities towards riboflavin. The ternary WTGr modified GCE shows the highest electrocatalytic activity due to synergetic interactions between the metal oxide and graphene. The electrochemical observations are supported by the SEM, HRTEM, XRD, UV-Vis, Zeta potential (ζ) and size data. The sensor shows a wide linear range 20 nM–2.5 μM with a detection limit 25.24 nM and sensitivity (4.249×10⁻⁸ A/nM). The fabricated sensor is validated in real samples.     

氧化钛负载脱硝催化剂的碱中毒过程：氧化钒的保留和氧化钨的牺牲

V2O5-WO3/TiO2催化剂目前已广泛用于电厂和工业锅炉燃烧废气脱硝,但燃烧原料煤及石油中含有的杂质元素碱金属与碱土金属元素可吸附在催化剂上,不仅会减少催化剂酸性位的数量,还会与催化活性元素结合生成惰性物种,导致催化剂失活。因此,已有许多有关钒钨钛催化剂碱中毒的研究,从催化剂的氧化还原能力、酸性位损失及表面孔结构等方面进行了讨论。但这些研究大多集中在碱中毒对活性组分V2O5的影响及中毒催化剂的活性变化,很少涉及催化剂中WO3的作用,也缺乏有关不同活性元素与钾盐反应的实验证据。本文采用过量浸渍法制备了不同钒和钨含量的钒钨钛催化剂,研究了氯化钾对其氨法选择性催化还原(NH3-SCR)活性的失活效应。利用感应耦合等离子体、N2吸附、拉曼光谱、H2程序升温还原、NH3吸附红外光谱和NH3氧化活性等手段对新鲜和中毒催化剂的性质进行了表征,特别探讨了V2O5和WO3对催化剂抗碱中毒能力的贡献。
　　催化剂活性测试结果表明, V2O5含量越高,活性温度窗口越宽,而且含有WO3的三元催化剂活性高于V2O5/TiO2二元催化剂。催化剂的BET比表面积和孔结构取决于TiO2载体,随活性组分配比变化不大,说明催化剂物理结构性质并非影响活性的主要因素。原位红外光谱及H2程序升温还原测试结果表明,随V2O5含量提高,催化剂表面Br?nsted酸性位数量及氧化还原能力提高。作为反应的主要活性物种, V2O5在碱中毒处理后变成惰性的偏钒酸钾KVO3,使催化剂中Br?nsted酸性位减少,热稳定性下降,并削弱了催化剂的氧化还原能力,因此低钒含量的催化剂容易严重中毒失活。在高钒负载量(3%)时,部分V2O5在碱中毒后得以保留,从而使催化剂保持了一定的脱硝催化活性。
　　另外, WO3能给催化剂表面提供热稳定的酸性位,虽然WO3自身的氧化还原能力差,但其能改善V2O5的分散性,从而提高V2O5-WO3/TiO2催化剂的活性。除此之外, WO3在催化剂碱中毒过程中还能扮演牺牲剂,与钾反应生成钨酸钾(K2WO4),即在V2O5与钾离子结合形成KVO3的同时,部分WO3也会与钾反应形成K2WO4,可以使三元催化剂保留更多的活性V物种。因此,在所研究的催化剂中,高钒负载量的V2O5-WO3/TiO2催化剂表现出最好的抗碱中毒能力。
　　活性影响因素分析表明,对于新鲜催化剂,其表面吸附的NH3量足够多,催化剂活性与表面酸性相关度不大,脱硝效率主要取决于催化剂的氧化还原能力。但是,对于碱中毒处理后的催化剂,其表面吸附NH3的能力大大削弱,这时脱硝效率除了受催化剂氧化还原能力影响,在很大程度上也依赖于催化剂的表面酸性。     

钨合金的冲击动力学性质及细微观结构的影响

简单介绍了钨合金(主要为W-Ni-Fe)的制备工艺和常用热处理方法,其后着重从动 态力学性能、剪切带的实验观察和研究、细微观结构对材料力学性能的影响等几方 面总结和评述了近年来针对钨合金取得的主要结果.并在文章的最后初步提出了有 前景的几个研究方向.     

EAST新型下偏滤器冷却结构 传热性能数值模拟

为实现EAST装置超400s长脉冲高约束模、10MW加热功率下的稳态运行，需对现有的下碳偏滤器进行升级改造，拟采用钨串结极水冷却系统，热通量控制在水冷钨铜第一壁材料允许的稳态的10MW·m^-2。在对下钨偏滤器的冷却结极传热性能进行数值模拟仿真研究的基础上，研究了多种以钨串单元为基础的冷却结极，提出了一种新型下钨偏滤器水冷结极设计，幵建立了满足传热要求的EAST装置新型下钨偏滤器单元结构模型。